阳极氧化铝丝印油墨

耐*阳极氧化铝丝印油墨销售厂家！

1、适用范围：产品主要用于金属、电镀、氧化铝、电解板、铝塑板、喷（烤）漆、喷塑等制品的丝印及移印。

2、产品特性：亮光、免烘烤、耐*、耐手汗、耐水泡、耐冲压。

3、稀释剂：用公司B-03专用稀释剂或783稀释油墨，用718洗网水清洗网版。

4、固化剂：单组份使用，不需要添加固化剂；如有特殊要求可选择添加本公司JS-9固化剂用于增加油墨附着力及性能，添加量为10%-15%。

5、油墨调配：开罐使用前应充份搅拌，然后取所需量油墨加入稀释剂稀释至合适的印刷粘度进行印刷。

6、网版及刮胶：适合80T-140T（200目-350目）聚脂网纱，聚氨脂PU油性刮胶。

7、干燥条件及时间：

干燥温度

25℃

60℃

80℃

100℃

干燥时间

24小时

40分钟

30分钟

20分钟

产品烘烤温度不可超过100℃。

【性能检测】

1、3M胶带划百格测试：**无脱落

2、耐冲压测试：1mm厚铝板180°折弯无变化。

3、耐*测试：用脱脂棉沾浓度99%工业*以500G力水平来回50次无脱色。

4、耐手汗耐试：用大拇指紧压印刷面5分钟后，再用力来回磨擦100次无脱色。

5、耐水性测试：用常温自来水浸泡24小时，3M胶带划百格测试，**无脱落。

【注意事项】

1、先小量试印确认符合要求后再批量生产。

2、做好承印物的表面清除油脂及杂质工作，以促进附着效果。

3、附着力、硬度、耐酸性、耐*性、耐化学品性、抗划伤性、耐磨性等性能的检测，

需要完全固化后方可检测。

4、未经允许情况下，不得将系列油墨与其它类型油墨混用及配色。

5、油墨，稀释剂使用及储存时严禁烟火。

 The products are mainly used in screen printing and the printing of various kinds of metal, glass, vacuum plating, electroplating, electrophoresis, water anodic alumina, electrolytic plate, aluminum plate, plastic spraying, dusting, electrostatic spray painting, paint surface and various ceiling oxide board, mirror panels, coated board, roller coated board and other products.

2, product characteristics: light, good adhesion, fast drying, stamping resistance.

3, diluent: with our B-03 special thinner or 783 open oil, washing network water cleaning screen with 718.

4, curing agent: one component use, can also choose to add our JS-10 special curing agent is used to increase the ink adhesion and physical and chemical resistance.

5, printing ink allocation methods: open cans to stir well, take appropriate amount needed to dilute ink printing viscosity. If you need to add curing agent, first add curing agent after mixing and set aside for 10 minutes, and curing agent for ink completely crosslinking after dilution.

6, the drying time: dry, dry time table for 5-10 minutes, work time within 24 hours, 80 degrees bake for 20 minutes can be dried quickly.

7, adding curing agent after the use of time: 4-6 hours, expired please abandoned, residual ink Unrecyclable.

[detection] performance

1, 3M tape row adhesion test: ** without shedding

2, stamping resistance test: 1mm thick aluminum 180 degree bend without change.

3, alcohol resistant test: with cotton dipped in 99% alcohol concentration of industry to 500G stress level and back 200 times without decolorization.

[note]

1, the first small try printing again after confirmation of compliance with the requirements of mass production.

2, do a good job in the substrate surface to remove grease and impurities, in order to promote the adhesion effect.

Detection of 3, adhesion, hardness, acid resistance, alcohol resistance, chemical resistance, scratch resistance, abrasion resistance and other properties,

Fully cured before detection.

4, without permission, may not use the series of ink and other types of ink mixing and matching.

5, ink, fireworks is strictly prohibited the use of thinner and storage.

6, the use of ventilation conditions attention the construction site is good, try to avoid direct contact with skin.

7, this product is inadvertently splashed entrance, nose, eyes, ears, use a large number of water washing or direct help doctor.