美国GE模块IC754VGB06CTD

厦门圣企机电设备有限公司

代工:15159233533（微信）

固话:0592-6081295

QQ:2587258111

辅助触头:与断路器主电路分、合机构机械上连动的触头,主要用于断路器分、合状态的显示,接在断路器的
控制电路中通过断路器的分合,对其相关电器实施控制或联锁。例如向信号灯、继电器等输出信号。塑壳断路
器壳架等*额定电流100A为单断点转换触头,225A及以上为桥式触头结构,约定发热电流为3A壳架等*额定
电流400A及以上可装两常开、两常闭,约定发热电流为6A。操作能次数与断路器的操作能总次数相同
触头:用于断路器事故的触头,且此触头只有当断路器脱扣分断后才动作,主要用于断路器的负载出
现过载短路或欠电压等故障时而自由脱扣,触头从原来的常开位置转换成闭合位置,接通辅助线路中的指
示灯或电铃、蜂鸣器等,显示或提酲断路器的故障脱扣状态。由于断路器发生因负载故障而自由脱扣的机率不
太多,因而触头的寿命是断路器寿命的1/10。触头的工作电流一般不会1A
分励脱扣器:分励脱扣器是一种用电压源激励的脱扣器,它的电压与主电路电压无关。分励脱扣器是一种远距
离操纵分闸的附件。当电源电压等于额定控制电源电压的70%-110%之间的任一电压时,就能可靠的分断断
路器。分励脱扣器是短时工作制,线圈通电时间一般不能15,否则线就会被烧毁。塑壳断路器为防止线圈烧
毁,在分励脱扣线圈串联一个微动开关,当分励脱扣器通过衔铁吸合,微动开关从常闭状态转换成常开,由于
分励脱扣器电源的控制线路被切断,即使人为的按住按钮,分励线圈始终不会再通电这就避免了线圈燒损情况
的产生。当断路器再扣合闸后,微动开关重新处于常闭位置
欠电压脱扣器:欠电压脱扣器是在它的端电压降至某一规定范围时,使断路器有延时或无延时断开的一种脱扣
器,当电源电压下降(甚至緩慢下降)到额定工作电压的70%至35%范围内,欠电压脱扣器应运作,欠
扣器
在电源电压等于脱扣器额定工作电压的35%时,欠电压脱扣器应能防止断路器闭合;电源电压等于或大于85%欠
电压脱扣器的额定工作电压时,在热态条件下,应能*证断路器可靠闭合。因此,当受保护电路中电源电压发
生一定的电压降时,能自动断开断路器切断电源,使该断路器以下的负载电器或电气设备免受欠电压的损坏
使用时,欠电压脱扣器线圈接在断路器电源侧,欠电压脱扣器通电后,断路器才能合闸
为满足轨道应用的需求条件,GE为您提供了完整系列的接触器、电动机保护开关和小型线路断路器。所有这
些元件都含特殊树脂,符合未来的prEN455452标准的要求。已获得多项认证例如U和csA等),可以在范围内广
泛运用。美国GE模块IC754VGB06CTD美国GE模块IC754VGB06CTD

IC200MDL741CA OUT 24VDC POS .5A ESCP 16PT CONF COAT

IC200MDL741LT OUTPUT 24VDC POS LOGIC 0.5A PER PT (1 GROUP OF 16) W/ESCP 16PT (LT)

IC200MDL742 Output 24VDC POS LOGIC 0.5 amp per point(2 group of 16) with ESCP 32 points

IC200MDL742LT OUTPUT 24VDC POS LOGIC 0.5A PER PT (2 GROUPS OF 16) W/ESCP 32PT (LT)

IC200MDL743 Output 5/12/24VDC NEG LOGIC 0.5A per point (1 group of 16) 16 points

IC200MDL743LT OUTPUT 5/12/24VDC NEG LOGIC 0.5A PER PT (1 GROUP OF 16) 16PT (LT)

IC200MDL744 Output 5/12/24VDC NEG LOGIC 0.5A per point (2 groups fo 16) 32 points

IC200MDL744LT OUTPUT 5/12/24VDC NEG LOGIC 0.5A PER PT (2 GROUPS OF 16) 32PT (LT)

IC200MDL750 Output 12/24VDC POS LOGIC 0.5A per point (2 groups of 16) 32 points

IC200MDL750CA Conformal Coated Output 12/24VDC POS LOGIC 0.5A per point (2 groups of 16) 32 points

IC200MDL750LT OUTPUT 12/24VDC POS LOGIC 0.5A PER PT (2 GROUPS OF 16) 32PT (LT)

IC200MDL930 Output relay 2.0 amps per point isolated form A, 8 points

IC200MDL930CA OUT  RELAY 2A ISO FORM A   8PT conf coat

IC200MDL930LT OUTPUT RELAY 2.0A PER PT ISOLATED FORM A 8PT (LT)

IC200MDL940 Output relay 2.0 amps per point isolated form A, 16 points

IC200MDL940CA OUTPUT RELAY 2A ISO FORM A 16PT MODULE ConFORMAL COATED

IC200MDL940LT OUTPUT RELAY 2.0A PER PT ISOLATED FORM A 16PT (LT)

IC200NAL110 10 point PLC, (6) 12VDC in, (4) Relay Out, (1) Analog Input (0-10VDC, 8 bit), 12VDC Power Supply

IC200NAL211 10 point PLC, (6) 24VDC In, (4) Relay Out, (1) Analog Input (0-10VDC, 8 bit), 24VDC Power Supply

IC200NAL211-24 Qty 24, 10 point PLC, (6) 24VDC in, (4) Relay Out, (1) Analog Input (0 -10VDC, 8 bit), 24VDC Power Supply

IC200NDD010 10 point PLC, (6) 12VDC In, (4) 12VDC Out, 12VDC Power Supply

IC200NDD101 10 point PLC, (6) 24VDC In, (4) 24VDC Out, 24VDC Power Supply

IC200NDR001 10 point PLC,(6) 24VDC In, (4) Relay Out, 24VDC Power Supply

IC200NDR001-24 Qty 24, 10 point PLC, (6) 24VDC In, (4) Relay Out, 24VDC Power Supply

IC200NDR010 10 point PLC, (6) 12VDC In, (4) Relay Out, 12VDC Power Supply

IC200PBI001 Remote I/O Profibus DP network interface unit

IC200PBI001CA Remote I/O Profibus DP network interface unit conformal coated.

IC200PKG001 PLC starter kit CPU001

IC200PKG010 VersaMax Modular PLC starter kit.  Kit includes CPUE05.

IC200PKG101 I/O starter kits, Genius NIU

IC200PKG102 I/O starter kit Profibus-DP NIU

IC200PKG103 I/O starter kit DeviceNet NIU

IC200PKG104 VersaMax Ethernet NIU starter kit with I/O.

IC200PNS001 PROFINET Scanner (PNS) module interfaces a remote node of VersaMax modules to a PROFINET IO Controller. Two 10/100 Mbps copper interfaces. Requires Proficy Machine Edition 7.0

IC200PNS001CA Conformal Coated. PROFINET Scanner (PNS) module interfaces a remote node of VersaMax modules to a PROFINET IO Controller. Two 10/100 Mbps copper interfaces. Requires Proficy Machine Edition 7.0

IC200PNS002 PROFINET Scanner (PNS) module interfaces a remote node of VersaMax modules to a PROFINET IO Controller.  Two 100Mbps Multi-Mode fiber (MMF) ports.  Requires Proficy Machine Edition 7.0.

IC200PNS002CA Conformal Coated.  PROFINET Scanner (PNS) module interfaces a remote node of VersaMax modules to a PROFINET IO Controller.  Two 100Mbps Multi-Mode fiber (MMF) ports.  Requires Proficy Machine Edition 7.0.